Your cart is currently empty!
Flooring, Ceiling, And Everything In Between In A Sprinter Van
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7391.jpg)
Flooring
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7387.jpg)
I purchased a 1.8sqm pack of laminate flooring from Bunnings.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7388.jpg)
The planks lock into each other.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7391.jpg)
I ran the planks width weights over the floor ribs.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7394.jpg)
I had to cut into the floor matt that extended past the front seats.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7395.jpg)
On the last plank I had to route a channel for the cable to the starter battery as the channel between the ribs ended.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7474.jpg)
A strip of aluminium right angle tied the whole thing together. The floor is essentially held in place by the trim that surrounds it.
Ceiling
I needed a way to contain the polyester insulation batts on the ceiling. I see most people installing tongue and groove boards or sheets of plywood. I didn’t see the benefit in this mainly due to the extra weight. I chose to suspend the boards with battens of Tasmanian Blackwood.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7233.jpg)
I had to cut the Blackwood down to size from 25 x 125mm stock with my Brother’s Festool plunge cut circular saw.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7232.jpg)
The strips would then hold up sections of calico.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7234.jpg)
The battens were attached with bolts into threaded inserts with a nylon spacer.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7235.jpg)
Side panel and trim
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7204.jpg)
I crafted these battens out of Tasmanian Blackwood.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7222.jpg)
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7236.jpg)
9mm ply was decorated with an old piano book.
![](https://www.vancatmeow.com/wp-content/uploads/2020/02/IMG_7241.jpg)
The batten pair will be used to hold a shelf while a TV will be mounted on the other.
- Building a Van Home for a Cat (and Two Humans)
- Finishing Touches And Extra Storage Ideas In A Sprinter Van Conversion
- Flooring, Ceiling, And Everything In Between In A Sprinter Van
- Van Storage With Hanging Space, Locking Drawers, And Suspended Tubs
- Building The Framework For A Bedbase, Kitchen, Cupboards In A Sprinter Van
- Blind Threaded Inserts Hold The Van Together
- Building A Custom Roof Ladder For a Sprinter Van
- Insulation And Ventilation for a Sprinter Van
- Building A 12v Electrical System For A Sprinter Van
- Custom Roof Rack – Sprinter Van Build
![Profile Photo](https://www.vancatmeow.com/wp-content/uploads/2020/12/IMG_0698-150x150.jpg)
Van Cat Meow
As seen on:
Lonely Planet
The Daily Telegraph
Business Insider
People Magazine
Sunrise TV
Buzzfeed
Mashable
![](https://www.vancatmeow.com/wp-content/uploads/2016/05/cat.png)